/ Register

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by poorboy

  1. poorboy
    Post

    Engine Issues

    hey nathan, how did u go with prices on rings etc.
    Post by: poorboy, Jan 16, 2009 in forum: Yamaha 250cc In-Line 4's
  2. poorboy
    Post

    leaking coolant

    ok i finally got all my parts yesterday and put it all together. was easy to do and no more leaks yay. but bad news is that its blowing more smoke...
    Post by: poorboy, Jan 16, 2009 in forum: Yamaha 250cc In-Line 4's
  3. poorboy
    Post

    leaking coolant

    sorry guys, what i was meaning was i can buy the internals separately for those prices which totals bout $141 i think or i could have bought a...
    Post by: poorboy, Jan 12, 2009 in forum: Yamaha 250cc In-Line 4's
  4. poorboy
    Post

    leaking coolant

    i got the seal out so now i know it will an be easy diy job.i rang yamaha and ordered my parts. theese are the prices they gave me: impella- $52...
    Post by: poorboy, Jan 11, 2009 in forum: Yamaha 250cc In-Line 4's
  5. poorboy
    Post

    leaking coolant

    yer it had lost 500ml of coolant so that why.lol. i just went down and pulled the water pump apart and the seal behind the impeller is stuffed and...
    Post by: poorboy, Jan 1, 2009 in forum: Yamaha 250cc In-Line 4's
  6. poorboy
    Thread

    leaking coolant

    hi all. i went for a big ride yesterday and half way home my bike started getting hot(needle width off red) and wouldn't cool down and just...
    Thread by: poorboy, Jan 1, 2009, 9 replies, in forum: Yamaha 250cc In-Line 4's
  7. poorboy
    Post

    Looking at fizzer with issues- what do you think is wrong??

    hey brad, i'm not real good at this sorta thing but i'll give my 2 cents anyway. now i'm assuming that to get it running u had to disconnect the...
    Post by: poorboy, Oct 31, 2008 in forum: Yamaha 250cc In-Line 4's
  8. poorboy
    Post

    Goodridge hoses

    o ok that makes sense. thanks, that would most certainly be a good idea. brake lines might have to wait for a while as i am saving to get new...
    Post by: poorboy, Oct 31, 2008 in forum: Yamaha 250cc In-Line 4's
  9. poorboy
    Post

    Goodridge hoses

    dontz125 said: what is the difference between bleeder and non bleeder banjo bolt
    Post by: poorboy, Oct 26, 2008 in forum: Yamaha 250cc In-Line 4's
  10. poorboy
    Post

    Goodridge hoses

    ok thanks, it would have been good if they did ay. hey to go to a 2 hose sett up, all i would need is the longer twin hose banjo bolt up top and...
    Post by: poorboy, Oct 24, 2008 in forum: Yamaha 250cc In-Line 4's
  11. poorboy
    Post

    Goodridge hoses

    how did u go with the 400 lines okee. did they fit ok. i was thinking about doing the same thing myself.
    Post by: poorboy, Oct 23, 2008 in forum: Yamaha 250cc In-Line 4's
  12. poorboy
    Post

    floating rotor floating too much

    does any one know if a tzr250 front disk will fit a 89 3LN fizzer
    Post by: poorboy, Oct 23, 2008 in forum: Yamaha 250cc In-Line 4's
  13. poorboy
    Post

    floating rotor floating too much

    yer i think i will clean out my rear caliper as it was hard to push pistons back in. but the front are ok i thing cause i can push them back in...
    Post by: poorboy, Oct 23, 2008 in forum: Yamaha 250cc In-Line 4's
  14. poorboy
    Post

    floating rotor floating too much

    Dave said: in cars and trucks i have found this too, that is why i assumed it normal on my bike, but then i came and read the forums.
    Post by: poorboy, Oct 21, 2008 in forum: Yamaha 250cc In-Line 4's