/ Register

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Search Results

Search Again
  1. Marius
    Post

    Help Carb issues - GSXR

    Gas anilizer at workshop at work Looking at putting on 2 aftermarket cone filter but not if it means I have to re-jet or richening the system
    Post by: Marius, Mar 25, 2015 in forum: Suzuki 250cc In-line 4's
  2. Marius
    Post

    Help Carb issues - GSXR

    Hi guys finally my tech at work got a little bit of time to work on my bike. He set the A/F ratio to 13:7 and the clip on the slide needle to...
    Post by: Marius, Mar 25, 2015 in forum: Suzuki 250cc In-line 4's
  3. Marius
    Post

    Help Carb issues - GSXR

    Guys did not do the settings yet the bike is at our workshop and for the 2 day's we were to busy at work to touch it. Will update once our...
    Post by: Marius, Mar 22, 2015 in forum: Suzuki 250cc In-line 4's
  4. Marius
    Post

    Help Carb issues - GSXR

    Hi Kiffsta I took that pipe of did not put new pipes yet but she idle for almost half an hour without spitting fuel, but won't start without choke...
    Post by: Marius, Mar 20, 2015 in forum: Suzuki 250cc In-line 4's
  5. Marius
    Post

    Help Carb issues - GSXR

    Thanks Kiffsta will remove that pipe and put 2 individual pipes on any specific routing where they should go. And thanks to all the guys you all...
    Post by: Marius, Mar 19, 2015 in forum: Suzuki 250cc In-line 4's
  6. Marius
    Post

    Help Carb issues - GSXR

    hi Stu between the 2 carb om the front there's a vacuum pipe going from one carb to the other but on the workshop manual the rightside carb got a...
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  7. Marius
    Post

    Help Carb issues - GSXR

    Hi Maelstrom I've fitted 2 new gaskets yesterday because mine was shot. Thanks
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  8. Marius
    Post

    Help Carb issues - GSXR

    will new needle seat and o-rings what's the correct spec for the floats just to make sure
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  9. Marius
    Post

    Help Carb issues - GSXR

    Does that mean 570 tube are for cylinder 2-3?
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  10. Marius
    Post

    Help Carb issues - GSXR

    Slides moving fine spring in centre. What I noticed the emulsion tubes are 2 types 2 with 12 holes and 2 with 6 holes I did not take note where I...
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  11. Marius
    Post

    Help Carb issues - GSXR

    Leaking out the bigger vents for the main jets [ATTACH]
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  12. Marius
    Post

    Mikuni BSW27 Carburetter rebuild kit

    Hi Ozbiker I've got a Gsx-r 250 GJ72A which I believe got the same carb. I busy rebuilding carb I took 2 types of needle jets(emulsion) tubes out...
    Post by: Marius, Mar 18, 2015 in forum: Suzuki 250cc In-line 4's
  13. Marius
    Thread

    Help Carb issues - GSXR

    Hi of recently bought. A Suzuki Gsx-r. 250 earlier version GJ72A had carb issue when I bought it. The problem is when I start it after a few...
    Thread by: Marius, Mar 18, 2015, 29 replies, in forum: Suzuki 250cc In-line 4's
Showing results 1 to 13 of 13
Search Again