/ Register

Recent Content by biglez

  1. biglez
    Post

    The Old & The New Paint Job

    Thats a no to the fairings, I prefer it naked. It would look nice with some bikini fairings. And no the bike is not on ebay or bike sales, but is...
    Post by: biglez, Apr 21, 2006 in forum: Yamaha 250cc In-Line 4's
  2. biglez
    Thread

    The Old & The New Paint Job

    OLD FRONT [img] NEW FRONT [img] OLD LEFT HAND SIDE [img] NEW LEFT HAND SIDE [img] OLD RIGHT HAND SIDE [img] NEW LEFT HAND SIDE [img]
    Thread by: biglez, Apr 20, 2006, 4 replies, in forum: Yamaha 250cc In-Line 4's
  3. biglez
    Post

    Top O' the mornin to ya!

    Nice!!! But one question, What is the bloke doing in the backround of the Bandit Photo?
    Post by: biglez, Apr 19, 2006 in forum: Yamaha 250cc In-Line 4's
  4. biglez
    Post

    Plastic Caliper thing

    Do a budget job on it. Some sort of tape (duct, speed, masking) over it. Keeps the dust out.
    Post by: biglez, Apr 6, 2006 in forum: Yamaha 250cc In-Line 4's
  5. biglez
    Post

    FZR250 / R6

    R6 engine width is around 296mm, I think a little wide for the fzr. The FZR400, from previous posts fits, but very snuggly. But I really dont...
    Post by: biglez, Apr 6, 2006 in forum: FZR250.com - Archives
  6. biglez
    Post

    Detailing your FZR

    I dont think polishing the frame with metal polish will work, due to the fact the frame painted. As for the rims, painting white would be easier....
    Post by: biglez, Apr 6, 2006 in forum: Yamaha 250cc In-Line 4's
  7. biglez
    Post

    RGV done

    Very Nice. As for the rattle, join http://www.gixxer.com and post.
    Post by: biglez, Mar 28, 2006 in forum: Yamaha 250cc In-Line 4's
  8. biglez
    Post

    Need help with paintjob ideas

    That was the same as mine before the fairings took flight whilst crossing an overpass. Here is a link to one of my posts with my polished rims....
    Post by: biglez, Mar 14, 2006 in forum: Yamaha 250cc In-Line 4's
  9. biglez
    Post

    fzr 3ln heating problem

    You can take the radiator guard off the front and fix a fan there.
    Post by: biglez, Mar 10, 2006 in forum: FZR250.com - Archives
  10. biglez
    Post

    Changing Oil in Japan

    Hey Jalakoo See if you can track down an english version of the workshop manual for the FZR250, Or translate the Japanese one. No one can seem...
    Post by: biglez, Mar 9, 2006 in forum: FZR250.com - Archives
  11. biglez
    Post

    Helmet Safety

    It should hug your face so that you cant chew gum, and its hard to get you fingers inside the helmet so you cant pick your nose.
    Post by: biglez, Mar 7, 2006 in forum: Yamaha 250cc In-Line 4's
  12. biglez
    Post

    fuel

    Check that your fuel lines from your tank are going into the right inlet in the fuel switch. (Reserve to reserve and fuel to fuel). In regards to...
    Post by: biglez, Mar 7, 2006 in forum: FZR250.com - Archives
  13. biglez
    Post

    Starting/overheat Issue

    There is a screw located on the bottom of each carbie bowl. They angle 45 degrees from the horizontal towards the ground. Next to each screw is...
    Post by: biglez, Mar 3, 2006 in forum: FZR250.com - Archives
  14. biglez
    Post

    Any advice welcome - Broken Bike/Broken heart

    Have you tried to restart it? The wreckers in Sydney rip you off big time. I rang a couple of sydney wreckers for my front mudguard and the...
    Post by: biglez, Mar 2, 2006 in forum: Yamaha 250cc In-Line 4's